7489 TM Hardware Technical specsIFB #7489 Page 1 of 2
IFB #7489 Transmission Hardware
Technical Specifications
Supply of Electric Utility Transmission Line Conductor Attachments &
Pole Hardware
A. PURPOSE
The City of Denton is providing information that will allow prospective suppliers to prepare
submissions to supply of Electric Utility Transmission Line Conductor Attachments & Pole
Hardware. The products will be received and distributed through a centralized distribution center
located at 901B Texas Street, Denton, TX 76209. Orders will be placed as needed over the contract
term.
B. SUBMISSIONS
Submissions shall be provided using the Exhibit 1, with supporting documentation as required.
Additional information clarifying the supplier’s product may be attached to their submission.
Pricing shall include all costs to deliver goods as specified in this specification. Any special fees
or commissions, and all freight for delivery to the City of Denton Warehouse and unloading costs
must be included in the quoted price. Item pricing shall be mutually exclusive, thus the City of
Denton reserves the right to choose the best valued item from different vendors.
C. QUALITY CONTROL
The manufacturer shall be responsible for the quality control of the manufacturing processes to
assure that all requirements of these specifications are met. However, the City reserves the right
to observe, to inspect and to require additional quality control investigations, either by its personnel
or an independently employed quality control investigator, at any or all stages of fabrication at the
manufacturer’s facilities. Failure to adequately maintain fabrication and quality of fabrication until
completion shall be grounds for cancellation of the order or any part thereof.
Field failure or field repairs required due to quality control failures or manufacturing procedures
shall be the responsibility of the manufacturer.
D. WRITTEN WARRANTY and GUARANTEES
Written guarantees shall include any limitations as to the nature of failure or time limitations. The
guarantee shall begin upon receipt of the accepted units, not on the date of manufacture.
Guarantees shall indicate whether or not it is made on a full replacement basis or a prorated basis
and if prorated then what are the terms. Manufacturer/supplier guarantees that the goods furnished
under this specification are of high quality and agrees to replace any goods found to be defective
during inspection, installation, or service for a minimum period of 12 months after unit is delivered
to Denton. All replacements by the manufacturer/supplier shall be free of charge F.O.B. at the
same delivery point called for in the original order. Replacements must be handled in a
professional and timely manner and in no case shall a replacement unit take longer than 60 days
to arrive in Denton after first being submitted for replacement.
Respondent guarantees that all products quoted and furnished under this agreement will be
accepted at any normally used United States approved repair and warranty shop should one be
available for the manufacturer’s product quoted. The City of Denton will not accept a
IFB #7489 Page 2 of 2
manufacturer’s product that was rejected or substandard and then sold to a broker for either resale
or scrap that would not be fully warranted by the original manufacturer.
The respondent must be an approved distributor by the manufacturer of these products, and is
authorized to sell the products to the City of Denton. The respondent also guarantees that the City
will be represented by the Manufacturer, should an issue arise, and that all manufacturer’s
warranties will be in effect for the life of the contract.
E. SPECIAL DELIVERY REQUIREMENTS
Deliveries shall be made between 8:00 AM -3:00 PM Monday through Friday, excluding holidays.
This location does have a forklift and dock available for offloading.
F. ACCEPTABLE MANUFACTURERS
DME will only accept submissions from specific manufacturers listed in the approved
manufacturers list below by specific item listed in Exhibit 1, Pricing Sheet.
1. Hubbell – Section A
2. Preformed – Section B
3. Maclean – Section C
4. Hughes – Section C
5. Aluma Form – Section C
6. Sefcor – Section C
7. NH Industries – Section C
8. Hubbell/Ohio Brass - Section D
The City has implemented a pre-approval process for substitution commodities and services. The
commodity approval form can be obtained via email (crystal.westbrook@cityofdenton.com).
Supporting documentation or samples must be submitted for review by Purchasing, Engineering,
field crews, QAG (Quality Assurance Group), and the manager of DME. Testing may be required
and may take substantial time to review. Vendors are encouraged to submit forms and samples
for consideration on the next solicitation for similar items.